Ремонт: Ноутбуков, Компьютеров https://vlab.su/ |
|
IT8985E EC-flash programmer https://vlab.su/viewtopic.php?f=181&t=42626 |
Страница 1 из 1 |
andromedax [ 24 фев 2016, 16:38 ] | |
Заголовок сообщения: | IT8985E EC-flash programmer |
How can I setup IT8985E programmer in order to read and write EC-flash? (KSO3, KS17, etc) I have no problems with KB9012QF but don't know how for IT8985E. Thanks. Вложение: ScreenShot 237.jpg
|
andromedax [ 25 фев 2016, 17:15 ] | |
Заголовок сообщения: | Re: IT8985E EC-flash programmer |
More about the problem: When I select ITE_chip at main menu, it opens a new window where I can set all the pin contacts in the keiboard connector, but when I finish an click any button, the folowing message appears: Number of VCOM ports found on the machine: 1 Âåðñèÿ FW ïðîãðàììàòîðà -> V41 It is necessary to update the firmware programmer! Any Ideas? |
Biquad [ 27 фев 2016, 20:05 ] | |
Заголовок сообщения: | Re: IT8985E EC-flash programmer |
andromedax писал(а): More about the problem: When I select ITE_chip at main menu, it opens a new window where I can set all the pin contacts in the keiboard connector, but when I finish an click any button, the folowing message appears: Number of VCOM ports found on the machine: 1 Âåðñèÿ FW ïðîãðàììàòîðà -> V41 It is necessary to update the firmware programmer! Any Ideas? Hi! andromedax? try this one : 1. Go to https://drive.google.com/folderview?id= ... NpMVU#list download file RUS manual for ITE and translate it :) You need update programmer firmware to version ITE_PROJ_M88_ver 11_08_15.hex : https://drive.google.com/folderview?id= ... NpMVU#list Then you need program programmer firmware every time, when switch beetwen KB9012 and ITE: for 9012 file M88_ALLPCB_4.1 .hex for ITE file ITE_PROJ_M88_ver 11_08_15.hex Firmware update utility chip45boot2_GUI_V1.13.7z: https://drive.google.com/folderview?id= ... NpMVU#list |
Vertyanov_SS [ 27 авг 2017, 14:42 ] | |
Заголовок сообщения: | Re: IT8985E EC-flash programmer |
Подниму эту тему, чтобы внести ясность и более простой способ описать. Для пользователей версии 2, нужно скачать программное обеспечение из этой темы Нам нужно для версии плат 2.X. 1 запускаем оболочку, выбираем ENE (или любой другой режим) 2 жмем на программаторе кнопку сброса и ДЕРЖИМ ее 3 нажимаем старт в оболочке 4 когда появится новое окошко - отпускаем кнопку на программаторе Должен пойти процесс прошивки. Проверьте работу с другими режимами. Raise this topic to clarify and more simple way to describe. For users of version 2, you need to download the software from this topic We need for version 2.X boards. 1 start the shell, select ENE (or any other mode) 2 Press the reset button on the programmer and KEEP it 3 press the start in the shell 4 when a new window appears - release the button on the programmer The process of firmware should go. Check the operation with other modes. |
Страница 1 из 1 | Часовой пояс: UTC + 4 часа |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |